Continental to present an innovative emissions control solution for downsized turbocharged gasoline engines at 37th Vienna Motor Symposium

• New Real Driving Emissions (RDE) legislation will strictly regulate NO_x emissions under all driving conditions, requiring high catalyst efficiency across a wide engine operating range
• Substantial reductions in nitrogen oxide emissions are also required by the US SULEV 30 emissions standard
• Close-coupled annular catalytic converter developed by Continental supports near-complete NO_x conversion in turbocharged gasoline engines

Vienna, Regensburg, Lohmar, 18-Apr-2016 — /EuropaWire/ — The international technology company Continental has chosen the 37th Vienna Motor Symposium to present an innovative emissions control solution for downsized turbocharged gasoline engines. The introduction of Real Driving Emissions legislation will require vehicles with this widely used engine concept to meet strict nitrogen oxide (NO_x) limits in all driving situations. This poses a new challenge by demanding efficient NO_x reduction across a very broad spectrum of engine operating conditions, and not “just” in the current test cycles. However, the existing close-coupled catalytic converters of today offer little margin for any further improvements in lambda distribution. On the US front meanwhile, the LEV III SULEV 30 standards stipulate a 70% reduction in fleet-average nitrogen oxide emissions by 2025.

“In order to meet RDE and SULEV 30 legislation on NO_x emissions, a 3-way catalytic converter must achieve a conversion rate close to 100%. That is only possible, if efficient NO_x reduction is maintained uniformly in all operating situations,” says Dr. Markus Distelhoff, Executive Vice President Fuel & Exhaust Management Business Unit in Continental‘s Powertrain Division. “The innovative ring catalyst in combination with our LS microstructured metal foil will play an important role in meeting this requirement.”

NO_x Reduction: Leaving Nothing to Chance

High-performance 3-way catalytic converters of today already achieve a NO_xreduction rate of 99%. But that still doesn’t go far enough, and a further efficiency hike must be targeted. For downsized turbocharged gasoline engines, this presents two challenges. Firstly, cylinder-to-cylinder variations in exhaust gas composition mean that the fuel-to-air ratio (lambda value) can deviate from the ideal value, adversely affecting NO_x conversion. The aim must be to avoid such cylinder influences on exhaust lambda, by flow mixing. However, this is difficult in the case of a close-coupled catalytic converter, because the down pipe to the catalytic converter is not long enough. This is why many new vehicles now feature a second – underfloor – catalyst to convert the remainder of the nitrogen oxide emissions, a solution which comes at the price of additional weight and increased exhaust back pressure.

Secondly, in some operating situations, the catalytic converter’s ability to achieve a consistent and uniform NO_x conversion rate can be adversely affected by the turbocharger system. This is because the opening of the turbine bypass valve (wastegate) above a certain engine speed affects the flow distribution, resulting in non-uniform exhaust flow. This can potentially lead to faster local ageing of the catalytic converter and to a deterioration in NO_xreduction performance.

Advantages of the Ring Cataly

Continental has developed an innovative solution to address both these challenges: The ring catalyst. An internal pipe running through the core of the ring catalyst and all the way along it provides the necessary additional length to allow better exhaust flow mixing. At the end of this pipe, the gas is redirected through 180°. Only then does it flow through the catalytically active portion of the catalyst, which surrounds the inner pipe like a sleeve. “This way the annular catalyst extends the flow path without extending the overall length of the catalyst. This allows the catalyst to be placed close to the engine, so there is no increase in the time required to reach light-off temperature for converting NO_xemissions,” says Rolf Brück, Head of Catalysts & Filters Product Line, Fuel & Exhaust Management. “With this design, the swirl effect from the turbocharger wastegate gas actually assists exhaust mixing in the internal pipe.”

The active section of the ring catalyst is wound from Continental’s innovative LS metal substrate. The longitudinal structures in this material generate micro-level turbulence in the exhaust stream, which helps to direct the nitrogen oxides more effectively towards the catalytically coated catalyst wall, where they are converted.

Contact for journalists
Simone Geldhäuser
Spokeswoman
Continental, Powertrain Division
Siemensstr. 12 / 93055 Regensburg
Phone: +49 941 790 61302
E-mail: Simone.Geldhaeuser@continental-corporation.com

###

Close-coupled annular catalytic converter developed by Continental supports nearcomplete NOx conversion in turbocharged gasoline engines.